HDAT2 (ALL-IN-ONE BOOT Version) –là chương trình để kiểm tra hoặc chẩn đoán các thiết bị ATA / ATAPI / SATA, SSD và SCSI / USB. Nó sẽ không thực thi trong phiên DOS của Windows.
Bạn nên tạo một đĩa mềm khởi động DOS hoặc CD / DVD và khởi động hệ thống của bạn cho nó và thực thi chương trình này từ đĩa mềm hoặc CD-ROM đó.
Chương trình HDAT2 có 2 cấp độ:
Kiểm tra thiết bị
- chức năng chính là kiểm tra và sửa chữa (để tái tạo) các thành phần xấu cho các thiết bị được phát hiện
- bạn nhận được nhiều thông tin về các thiết bị được phát hiện
Kiểm tra hệ thống tệp
- đọc / tìm / kiểm tra các mục (MBR, khởi động, thư mục, v.v.) của hệ thống tệp FAT12 / 16/32
- kiểm tra / loại bỏ (tái tạo) các bản ghi thành phần xấu, cờ trong bảng FAT
Features
• fully implemented commands: SET MAX, SET SECURITY, Device Configuration Overlay (DCO)
• device access with interrupt 13h, direct via ATA ports, with ASPI drivers
• detects ATA/ATAPI/SATA devices with on-board and add-on controllers
• detects devices on AHCI/RAID controllers (just only on ports 0-3)
• detects USB devices via USB ASPI driver or BIOS (if supported)
• detects SCSI hard drives via BIOS interrupt 13h or ASPI drivers
• other SCSI devices are detected via ASPI drivers only (must be loaded before);
• with ASPI drivers you will get more information about SCSI devices
• test and repair device for bad sectors (so far version 4.5.3 only)
• many different test-functions for hard drives
• resize hard drives which supports SET MAX ADDRESS/EXT
• (supports 28/48-bits LBA addressing modes)
• drive lock detection via security feature (Security Menu)
• S.M.A.R.T. functions for ATA/SATA and SCSI drives only
• information about devices (ATA/ATAPI, BIOS interrupt 13h, ASPI, EDD)
• sector viewer for devices (also for USB, ZIP, CD-data discs)
• to access ATA/SATA CD/DVD drive you don’t need any driver or MSCDEX
• enable/disable some features for direct-access devices
• Device Configuration Overlay (DCO) feature set
• (you can restore a full capacity or allow/disallow some feature sets of hard drive)
Known limitations:
• change SATA controller in BIOS from AHCI to IDE/ATA/legacy mode
• devices SATA/AHCI/RAID detect on ports 0-3 only
What’s New:
09.01.2023 7.5
NEWS:
- in SETUP added parameter 'AHCI allowed speed limit'
- change allowable speed of the SATA/AHCI interface
- new command line parameters (see HDAT2 /?):
/x=12 'disable test LOG'
/x=13 'enable INT13h IDENTIFY DEVICE' (this could hang!)
/U=x 'Detect AHCI WAIT timeout' in x-milliseconds
FIXES:
- better detection devices over INT13h (USB)
- checksum error for ACPI revision 0
- SMART error for NVMe
- detection for all AHCI ports
CHANGES:
- new layout for SMART Pending Defects log (0Ch)
- command line parameters for disable detection /D (see HDAT2 /?)
- the outdated item 'File system menu' is not available due to work on a new version
LIMITATION:
- to boot DOS you have to select CSM/legacy boot in BIOS instead of UEFI
Title Release: HDAT2.v7.5
Developer: Home Page
License: FreeWare
OS: Windows
Hướng dẫn : copy mã số ở trên paste vào Hex String ở dưới convert lấy link down nhé
Text to Hex Converter Online
Convert any string of text to its corresponding hexadecimal
online-toolz.com
Sửa lần cuối: